Difference between revisions of "User:Cyremann"
(Created page with " <!--MAKE AS MANY CATEGORIES AS YOU NEED-->") |
|||
| Line 1: | Line 1: | ||
| − | + | <gallery> | |
| + | |||
| + | </gallery> | ||
| + | {{Project|Creator=Cyremann | ||
| + | |Status=<onlyinclude> Your Status </onlyinclude> <!--LEAVE ONLYINCLUDES FOR STATUS HACK--> | ||
| + | |Born On=14:11, 19 October 2019 (CDT) <!--DO NOT EDIT --> | ||
| + | |Last Updated={{#time: H:i, d F Y| {{REVISIONTIMESTAMP}} }} (CDT) <!--DO NOT EDIT --> | ||
| + | }} | ||
| + | |||
| + | ==Overview== | ||
| + | I had a piece of black cherry log in my shop that was well seasoned, so I decide to try and make something from it. | ||
| + | My 3 year old really enjoys looking at colored lights, so I decided to make him a nightlight / lamp. | ||
| + | |||
| + | [https://imgur.com/a/P2IYevr Imgur Gallery of Progress] | ||
| + | |||
| + | I started by roughing out a cylinder on the wood lathe. I then used a drill press to make holes around the outside of that cylinder. | ||
| + | After that I used a 2-part epoxy with a small amount of acrylic paint to fill the holes with different colors. Once that was all hardened, I returned | ||
| + | to the wood lathe, turned the outside down, and hollowed out the interior. After much sanding it was finally smooth enough, and I coated the entire piece in | ||
| + | a clear epoxy. | ||
| + | |||
| + | I then needed a base and cap for the lamp. I though about casting something out of epoxy or turning something out of wood, but I wanted something heavier than that | ||
| + | so the sake of stability. I also wanted something that could act as a heat sink for the LEDs as well as a capacitive touch sensor. I decided to go with aluminum. | ||
| + | |||
| + | I was given some scrap aluminum, which I smelted down and poured into an empty tin can. After cooling, I used the metal lathe to turn it down into the desired shape. | ||
| + | A few drill press holes later and the base is basically finished, with the exception of final finishing an polishing. | ||
| + | |||
| + | I will be placing the electronics into the base of the lamp, and hopefully using the metal parts as a capacitive touch sensor for operation. I may (or may not) have two or | ||
| + | three levels of brightness that it can be cycled through. | ||
| + | |||
| + | I still need to turn the cap out. | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | [[Category:Lamp]] | ||
| + | [[Category:Casting]] <!--MAKE AS MANY CATEGORIES AS YOU NEED--> | ||
| + | [[Category:Lathe]] | ||
Revision as of 14:11, 19 October 2019
|
Creator: |
Overview
I had a piece of black cherry log in my shop that was well seasoned, so I decide to try and make something from it. My 3 year old really enjoys looking at colored lights, so I decided to make him a nightlight / lamp.
I started by roughing out a cylinder on the wood lathe. I then used a drill press to make holes around the outside of that cylinder. After that I used a 2-part epoxy with a small amount of acrylic paint to fill the holes with different colors. Once that was all hardened, I returned to the wood lathe, turned the outside down, and hollowed out the interior. After much sanding it was finally smooth enough, and I coated the entire piece in a clear epoxy.
I then needed a base and cap for the lamp. I though about casting something out of epoxy or turning something out of wood, but I wanted something heavier than that so the sake of stability. I also wanted something that could act as a heat sink for the LEDs as well as a capacitive touch sensor. I decided to go with aluminum.
I was given some scrap aluminum, which I smelted down and poured into an empty tin can. After cooling, I used the metal lathe to turn it down into the desired shape. A few drill press holes later and the base is basically finished, with the exception of final finishing an polishing.
I will be placing the electronics into the base of the lamp, and hopefully using the metal parts as a capacitive touch sensor for operation. I may (or may not) have two or three levels of brightness that it can be cycled through.
I still need to turn the cap out.
