Difference between revisions of "Member Grants 2018"

Revision as of 00:30, 5 October 2018

Selected Member Grants for 2018

Overview

The shop raised money from the pig roast and was also given money from a former member who loves us!

The money is divided into 4 pools of $300, $300, $100, and $100. We're going to use this wiki page to accept proposals and vote on what you want to do with the money. This can include shop improvements, tool purchases, anything that boosts shop moral (and is legal in the state of Alabama). Add your proposal to this page so that all will know. Proposals will have to include a deadline of when this project will be completed (unless the nature of the project precludes that) and an explanation of what you plan to do with one of the fund pool. Feel free to include multiple proposals, but make sure they're ones that you and other named members can carry out. Each proposal should cover Who (as in project leader and helpers), What (project details), When (start and completion dates), Where (where in the shop this will live, where your event will take place, etc.) and Why (why do you think this will help the shop - don't overthink it, I just like the 5W's). If the project doesn't get finished or the money is not all spent, it will be returned to the shop general fund after the project's finish date. If it doesn't make sense to have a finish date for the proposed pool, eg. "$100 set aside for propane", it will get recorded in the treasurer's book and Phil will cringe a little as the book gets a teensy bit harder to read. ;-)

Use of the discussion page is also encouraged.

• For the $300 proposals, please put your name\vote next to just two proposals.
• For the $100 proposals, please put your name\vote next to just two proposals.

Check back here for dates of when the Request for Proposal time ends, as well as which proposals win.

Please see Member Grants 2012 and Member Grants 2015 for examples of how proposals were made in the past.

$300 Proposals

Electronics Reflow Oven

• Who: tylercrumpton (talk)
• What: Purchase of a T962A Infrared Automatic Reflow Oven (300×320mm): LINK
• When: Immediately after the grants are awarded. (+ probably about 30 days for shipping)
• Where: To be installed upstairs near the PCB Pick and Place machine
• Why: We have a Pick and Place machine! It can help you assemble one or hundreds of electronics boards! Unfortunately, it's not that helpful unless you have an oven. The toaster oven has worked a little bit, but these machines work so much more reliably and quickly.
• How Much: $300.00 (with the remaining ~$50 to be covered by Tyler)
• Votes: tylercrumpton (talk)

Your Proposal here

• Who:
• What:
• When:
• Where:
• Why:
• How Much:
• Votes:

$100 Proposals

LoRaWAN Radio Gateway - Enable Free IoT for HSV

• Who: tylercrumpton (talk)
• What: Purchase and installation of one LoRaWAN Gateway device (something similar to this)
• When: 1 month to install the gateway and get it set up
• Where: To be installed on the radio mast outside of the shop
• Why: LoRa is an long-range wireless protocol that can be utilized by small and inexpensive modules. LoRaWAN gateways connect one of these modules to the Internet so that IoT devices like sensors and controllers can use the LoRa connection to publish or receive data from the Internet. Basically, one gateway can serve as an access point for devices in a multi-mile radius, often eliminating the need for a cell connection. The modules can be found for as little as $5 and can be connected to a Raspberry Pi, Arduino, or similar device. Monitor your beehive remotely, track your car with a GPS module, detect earthquakes, or do something completely different!
• How Much: ~$80
• Votes: tylercrumpton (talk)

Your Proposal here

• Who:
• What:
• When:
• Where:
• Why:
• How Much:
• Votes: